Once you've got the amount that you need for your sprayer, you're going to remove the lid from the measuring chamber side only.
Now instead of pouring to a hard angle into your sprayer with these bottles is best to go at a slight angle away from you.
This is going to help make sure that only the solution in the measuring chamber is going into your tank and more of the solution from the main area of the bottle is not rolling up behind and having you measure more than you intend it to. So we're going to go at a slight angle away to get all that solution in there and then now you're good to go. If your particular label calls for more solution than what the measuring chamber provides, you can always put the lid back on and rotate the bottle again.
If not, we're going to put the lid back on and securely store it. And you should be all set for the tip and pour application. Now we're going to move on to the squeeze and pour With the squeeze and pour bottle you want to make sure that you've removed both lids and checked for seals underneath them.
I've gone ahead and removed the seals in this case. This is going to help to make sure that the airflow for the squeeze and pour is going to work correctly as it acts somewhat as a vacuum as you squeeze the bottle to push the chemical into the measuring chamber. Once you've got it ready and you've removed the seals, you can remove the lid from the measuring chamber side and then you will slightly squeeze your bottle and you'll notice that the solution is going to run from the bottom of the bottle here up the straw and into your measuring reservoir.
We're going to do this gently you don't want to squeeze too hard to have the chemical come out too quick. Once you get the solution to the level that you need - and you may have to do this a couple of times to get that flow going and get those air bubbles to release So I had to push the bottle back a little bit just like you might do with a average 2-liter bottle or anything like that.
You want to get that air flow going then you can squeeze again and more of that solution will run up into your measuring reservoir once you get the amount you need which in this case we're going to run to the half ounce line on this particular bottle.
You can pour it directly into your spray tank and you don't have to worry about any extra mess or anything rolling from the rest of the bottle into it since you're controlling that as you squeeze the bottle. Once you're done, you'll replace that lid back on the bottle and then fill your sprayer the rest of the way with water and continue with your treatment.
If you have any questions, as always you can contact our customer service staff and if you like this video be sure to head over to our channel give it a thumbs up, hit that subscribe button, and check out our other DIY and how-to videos.
Thanks for watching! Inside, outside, and around the perimeter of structures, food handling areas, lawns, turf and ornamental trees and shrubs. NOT for use on food and vegetable gardens. Talstar is best applied with a sprayer. Always read the label completely before use. Use 0. Apply either as a crack and crevice, pinstream, spot, coarse, low pressure spray 25 psi or less or with a paint brush.
Apply as a coarse, low pressure, crack and crevice or spot spray to areas where pests hide, such as baseboards, corners, storage areas, closets, around water pipes, doors and windows, attics and eaves, behind and under refrigerators, cabinets, sinks, furnaces, stoves, the underside of shelves, drawers and similar areas.
Talstar P may be converted to a foam for residual treatment of voids or as a spot spray when visual marking of application is desired. Thorough application should be made to crack and crevices where evidence of bed bugs occurs. This includes bed frames, boxsprings, inside empty dressers and clothes closets and carpet edges, high and low wall moldings and wallpaper edges.
Do not use this product on bed linens, pillows, mattresses or clothes. Remove all clothes and other articles from dressers or clothes closets before application. Allow all treated areas to thoroughly dry before use.
Not recommended for use as sole protection against bedbugs. General application for crawling pests - Mix 0. Also spray entry points into the home such as around windows, pipes, doorways, etc. For general preventative treatment, apply Talstar P once every 3 months. In addition to the treatment around the foundation of the home as mentioned above, spray Talstar P on the underside of leaves on the lower-hanging branches of trees around the backyard or area where mosquitoes are a problem. You can also spray the underside of leaves on shrubs and ornamentals.
Do not apply when wind speed exceeds 10 MPH. Higher application volumes may be used to obtain the desired coverage of dense vegetation or landscaping materials. Apply as a full coverage foliar spray.
Use of a Chapin Slide Pump Sprayer will help reach higher into trees. Apply when larvae begin to hatch and spray larvae directly. Applications when larvae are young will be most effective. Chinch Bugs infest the base of grass plants and are often found in the thatch layer. Irrigation of the grass area before treatment will optimize the penetration of the insecticide to the area where the chinch bugs are located. Use higher volume applications if the thatch layer is excessive or if a relatively long mowing height is being maintained.
Chinch Bugs can be one of the most difficult pests to control in grasses and the higher application rates Up to 1 fluid oz. A hose end sprayer like the Chapin hose end sprayer may be used to apply Talstar P for lawn pests. Use up to 1. Higher volume applications may be more effective with some pests, so you may want to calibrate the sprayer to a lower rate for example, 0. Talstar P has an expanded label for treatment of Stink Bugs indoors, outdoors, on lawns, and on ornamental plants.
You can read lot of information about its application and precaution on the label. According to the man Talstar P formula as a liquid spray or via a fogger will give the most efficient results against pests. Talstar P does not harm vegetation, therefore, it is safe to use in lawns and gardens; however, it can indirectly harm human health when the fruits and vegetables from the garden are consumed by people.
Therefore it is advised not to spray the insecticide directly onto edible fruit and vegetable plant body. If your region experiences heavy rain, then it is recommended to apply it in every 21 days of interval. Yes, as long it is dried completely it is safe. You should evacuate your home before spraying and let it dry completely before occupying the house again. In warmer season, apply it every month while in cooler season when they are inactive, apply it every 3 months.
Talstar P is a water based product so it takes as much the time the water would take to dry when sprayed. In the case of bed bug treatment, use a higher concentration i. Yes, Talstar is safe to use around pets considering that you follow the instructions mentioned on the label diligently. Yes, Bifen and Talstar are essentially the same product. Talstar is a very effective insecticide that also acts as a repeller because of its residual properties that remains long after it is used.
Talstar P has a residual power of up to 90 days, which kills the insect and prevents their breeding. It usually is recommended to use 0.
However, in case of faster knockdown and longest residual lasting, it is suggested to use 1 floz of Talstar per gallon of water. There are also instructions available on the back of the label suggesting the quantity of Talstar to be used depending upon the surface area you wish you cover. A professional insecticide indeed, Talstar Pro kills and controls over 75 different species of insects ranging from bed bugs, mosquitoes, fleas, crickets, etc. While the above-mentioned Talsar Pro Insecticide can definitely help you deal with roaches, sometimes you need stronger and potent solutions to a heavy and growing roach infestation.
Customer Photos. Reviews Questions. Title of Review. How was your overall experience? Do you recommend this product? Thank you for submitting a review! Your input is very much appreciated. Share it with your friends so they can enjoy it too! Facebook Twitter. Clear filter. More Filters. United States. I recommend this product. Talstar Bifenthrin So far so good, too early to tell of proof.
Was this review helpful? Works great We had an ant problem in our camper we tried other products without much luck After one round of talstar no more ants. You may also like.
0コメント