It is important to keep the width regular and with the help of a bias tape gadget, the whole task of turning in the sides is made much easier. Further Reading: How to make bias tape. The subject of types of bias tape is certainly broader than a single piece of fabric cut on the bias.
Experiment with different fabrics and colors and add a few rows of decorative tape to a skirt or tablecloth. Keep learning new things and never be totally predictable in the styles, finishes and fashions you create. I am glad I found this it gives me a better understanding of how to use bias tape.
I also learned how to make my own bias tape as I am using this in vintage doll dressing. Now I can make beautiful bias for my Thumbelina dolls. Your email address will not be published. Share this article:.
Types of Bias Tape. Table of Contents. Comments Very good article with good explanation. Thank you. The most articulate and comprehensive article I've seen - thanks so much! Third , make sure all your fabric is pushed to the left of your needle. This may give you the wrong side of the fabric pointed in your direction. Now you can pin the seam binding to your fabric at this point but it is not necessary.
Fourth , place the delicate and sheer seam binding ribbon in place and have about half of it overhanging your edge. How far over depends on the thickness of your fabric. Fifth , stitch the seam binding ribbon in place till you get to the end of the fabric. Then cut the ribbon about 1 inch past the end of the fabric.
Next , fold the unsewn half of the ribbon over your hem. You may need to use pins here to make sure the ribbon stays where you want it. After you have folded the ribbon, iron it so it stays in place. After that , you want to return to your sewing machine and sew the last part of the seam binding in place. And you are done. You should have a beautiful-looking seam binding that does not detract from the overall look of your sewing project.
This can be a difficult task as corners are very hard to make look good when you try to seam bind them. There is a long process to getting these corners done well so they do not ruin your work or look bad.
One of the first steps you need to do is lay out your seam binding ribbon and see where the seams on it lay. You do not want the seam binding ribbon seams in the corners. So if they fall there, move them. Then back stitch for a few stitches and stop. Then fold the edge of the ribbon up in the corner till you get a degree angle. Now you fold the next row of seam binding ribbon over the folded edge and sew the two together.
After that you should cut the binding ribbon a tiny bit up to but not including or past your stitches and fold the ribbon over a bit. Then stitch it all into place. A little triangle of seam binding may appear during this process but you can trim it away easily. The newly cut piece of ribbon needs to be folded back over your sewing project, pinned into place and then sewn. One of the differences between the two sewing applications is that biased tape is cut on a degree angle or what is called the bias.
This tape is designed to stretch a bit which makes it very useful when you have a curve you have to sew through. Bias tape is better with armholes, necklines and finishing seams.
The seam binder ribbon is just that, a ribbon. It does add strength, but it is limited in its use and is best used to cover rough edges or seams. It also works on holding seams together. Twill tape is similar to seam binding in that it is a woven piece of ribbon only stronger. Where bias tape is good for being sewn around an edge of a garment to crate a finished hem, twill tape has more uses.
Besides reinforcing seams, twill tape is good for reinforcing button holes, etc. While bias tape is meant to be seen, twill tape is not. One of the biggest differences between the two applications is that seam binding ribbon does not stretch.
It is used as a stabilizer for those seams that tear easily. Bias tape is usually used on the seen portions of your sewing project. Binding is either centerfold, which means it comes pre-folded for easy wrapping around your unfinished edge, or flat, which needs to be folded before application.
Single-fold bias tape is made with strips of fabric that have been cut on the bias, sewn together in long strips, and used to bind raw fabric edges or add a pop of color. Double-fold bias tape is single-fold bias tape that has been folded in half and pressed with the single folds to the inside.
For a square quilt straight grain binding, meaning fabric strips cut cross grain or length-wise grain, will work well. Bias binding gets its name from the way the binding cloth is cut. There are three ways to cut your fabric: Lengthwise also known as Warp — runs parallel to the selvage and has little to no stretch.
Because it is made from yarns woven over and under the lengthwise yarns it has more stretch than lengthwise grain. Quality made sewing notions. Seam binding strengthens seams and prevents stretching.
It is a quick way of finishing off edges. Features a woven edge and is washable. Sandwich the edge in between one piece of folded binding and sew in place to prevent the edge from unraveling or stretching. And because Bias Tape has some stretch, it curves really nicely around curved edges of fabric……. Press your bias tape in half with wrong sides together. Pin the folded binding to your neck opening, aligning raw edges.
0コメント